![]() You don’t want to pound them in like how a brad nailer does, instead just give each dowel a few light taps to get them to sink down far enough into the hole to create a sturdy rail for your sockets. Due to the snug fit, the dowels won’t go all the way in on their own. Next you will use a hammer to hit each dowel lightly into the hole. The wood glue, while not needed, will help your dowels stay put for a longer period of time than the simple tight fit will. To secure them,you will want to place a dab of wood glue onto the end of the dowel. Since you used the same size drill press for each hole, the dowels will fit snug into each space. Once all of your dowels have been cut, the next step is to place them into the pre-drilled holes. Just don’t sand on the sides, since you will need the width to create a secure hold once your sockets are placed on them. Once you have cut all of your dowels, sand down the top edges to create a smoother area for the sockets to slide down onto. While it is a little extra work, for those who struggle with dowel cuts, this guide will help you get the right cut every single time. To help expedite and make the perfect cut each time, you may want to consider spending 5-10 minutes creating this perfect dowel cutting guide. The dowels will need to be cut to 1 3/4th lengths, this is long enough to fit into the board as well as offer a long enough support to hold each socket. However, the right sized dowel will give your sockets a snug fit so that you don’t need the addition of a magnet to hold them into place. The biggest difference between the two is that some socket rails can offer a magnetic addition to help hold the sockets in place. Wooden dowels work as well as the traditional metal or plastic socket rails that more stores sell. The 4 foot dowel pole will be more than enough, you should have some left over for additional projects. With the holes all drilled, your next step is to cut your dowels. No sanding is needed at this point, since you will want the holes to remain the correct sizing for the dowels to fit tightly into. ![]() This will make the drill bits angle upwards a hair, which will help them not slid off when hung on a wall. When creating the dowel holes, you can make them level or create an angled hole by adjusting the drill press 10%. The addition of wood glue in a later step will help hold the dowels into place. Depending on the depth of your wood piece you can drill all the way through or leave a shallow bottom. To match the dowel sizing you will need to use a 3/8th and 1/4th bits on your drill press. A drill press is the best tool to use for this project, however if you don’t have one handy then you can use cutting bits on your handheld drill to make the incisions. Once you have measured and marked, you are ready to start making the holes where the dowels will sit in. Keep in mind that for each socket you will be attaching a dowel, so make sure that you leave enough space between the sockets to grab as well as leave some space to mark the sizing in the following steps. Utilizing a ruler will give you an equal spacing so that you can use as much of the space provided accurately without having weird lines or sockets that are too close together. To give yourself a visual, you can also place each socket on the board to see the best spacing for your DIY socket organizer. You will want to use a ruler for this step to mark out the correct spacing for all of the socket sizes that you want. Once the board has been cut or trimmed to the right size, you can go ahead and sand down the edges or leave them natural if you don’t want them smoothed down. Where you want to place it will factor into the main boards size. This socket holder is designed to be placed in a drawer, sit on a table top or can even be hung on the wall to save space. If you don’t have one, you can pick up the best table saw for under $300, and still end up with a really good saw. ![]() Trim the board down to your desired length and width with any saw you have at home. The first step in this project is to prep your main board. To get started on this DIY socket holder project you will need: One of the following steps will help you measure out the area for sockets to sit so that you can equally space them to utilize as much of the board as possible. The open design of this socket holder is meant to hold them all as well as can hold a few extras if you have them. You can make this DIY socket holder as large or small as you need it to be, but with the difference between metric and standard sizes, the amount of socket spaces you have on hand may be quite a few. Unlike some of the best socket holders that you can buy, which are typically made from metal, I suggest using plywood or any other type of board that you already have in your garage or shop. To create a socket holder for your workbench at home you will need a flat piece of wood.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |